Palm Sliding Doors

guides

French Door Repair in Tampa: Sagging, Sticking and Leaking Doors and How Each Is Fixed

Written by the Palm Sliding Doors team · Published September 30, 2026 · 7 min read

French Door Repair in Tampa: Sagging, Sticking and Leaking Doors and How Each Is Fixed

French door repair in Tampa usually means one of four things: rehanging or replacing hinges on a door that has sagged, adjusting or replacing the threshold and sweep on a door that leaks, repairing the astragal and flush bolts on the inactive door so the pair locks properly, or replacing a fogged or broken glass unit. Most of it is done on a single visit, and a French door that sags, sticks or leaks is nearly always worth repairing before anyone talks about replacing it.

French doors swing on hinges instead of rolling on a track, meet in the middle on a strip called the astragal, and depend on a threshold seal a slider does not have. This guide walks through the problems Tampa Bay French doors develop and how each is repaired.

Why do French doors sag?

Weight and time. A French door panel with a full glass lite is heavy, and all of it hangs off three or four hinges on one side. The top hinge carries most of the load in tension, and over the years its screws loosen in the jamb, the hinge knuckles wear, or the jamb itself moves. The door drops at the latch side, rubs the threshold at the bottom corner and catches the head at the top.

Tampa Bay adds its own causes. Humidity swells wood doors and jambs, so a door that fit in February binds in August. Older concrete block homes in Seminole Heights, Temple Terrace and parts of South Tampa have wood bucks that have shrunk or softened, so the jamb the hinges screw into is no longer solid. And on a caged lanai, a door left open in a breeze gets pushed against its hinges constantly.

The fix, in order of how often it is enough. First, the hinge screws. Replacing the short factory screws in the top hinge with long screws that reach through the jamb into the framing pulls the door back up and squares it. Second, hinge replacement, when the knuckles are worn or the hinge has bent. Ball bearing hinges are the right choice for a heavy glass door. Third, shimming or re-securing the jamb when the buck behind it has moved. A door that has been sagging for years may also need the strike plate moved so the latch lines up again.

Why do French doors stick?

Sticking is sag’s close cousin, but it has extra causes worth separating.

Sag. The latch-side corner rubs. Fixed as above.

Swelling. Wood and some composite doors take on moisture in summer and rub along the whole edge. Planing the edge and sealing it properly stops it coming back. Fiberglass and aluminum doors do not swell, so on those, sticking is almost always hinges or alignment.

Weatherstripping. A compression weatherstrip that has hardened or been painted over makes the door hard to close and latch, and the latch does not reach the strike. New weatherstrip fixes it.

Threshold height. Some thresholds are adjustable, and one that has been cranked too high to stop a leak makes the door drag across it. The right answer is fixing the seal, not raising the threshold.

Frame racking. On older homes the whole opening can go slightly out of square. Small amounts are absorbed by adjusting the hinges and strike.

Why do French doors leak at the bottom?

The threshold. This is the most common French door complaint in Tampa Bay: a summer storm blows in from the west, the lanai floods, and water comes under the door.

A French door seals at the bottom with a sweep on the door meeting a threshold on the floor under compression. The sweep wears, the threshold’s rubber insert cracks in the sun, or the threshold was never sealed to the slab, and water blows under the sweep or wicks under the threshold.

Repairs, from simplest to largest. Replace the sweep and the threshold insert. Adjust the threshold up to meet the sweep. Re-bed the threshold in sealant on the slab, which means pulling it and setting it back down properly. Add a sill pan if the original installation had none, which is common on older doors. And on a door that faces the prevailing storm direction with no overhang, an exterior drip cap or rain deflector over the door is a small addition that stops most of the water before it reaches the threshold.

Leaks at the top or sides point to flashing or the frame not being sealed to the wall, a bigger repair than the threshold.

What is the astragal and why does it matter?

On a pair of French doors, one door is active and one is inactive. The inactive door is locked to the frame top and bottom with flush bolts, and the astragal is the vertical strip on its edge that the active door closes against. The active door’s latch and deadbolt engage in the astragal.

When the astragal is loose, bent or its weatherstrip has failed, the whole pair leaks air and water down the middle, the doors do not meet squarely, and the deadbolt may not throw fully. When the flush bolts are worn or the holes they drop into are stripped, the inactive door moves, and the active door has nothing solid to lock against. That is both a security and a weather problem.

Repair means re-securing or replacing the astragal and its weatherstrip, replacing the flush bolts or their strikes, and re-aligning the pair so both doors meet flush. It is done on the same visit as hinge work, because a sagging door and a misaligned astragal go together.

What about the glass?

French door glass is treated the same as sliding door glass. A foggy lite means the insulated unit’s seal has failed and the unit is replaced; the door stays. A broken lite is measured and replaced with a new tempered unit, because door glass in Florida must be tempered, or with a laminated unit on an impact-rated French door. Glass is made to size, so it is a two-visit repair: measure, then fit. Multi-lite French doors with individual small panes are more work per door but the principle is the same.

If the frame is fine and the only problem is fog, glass replacement is a straightforward repair. If several lites are fogged and the door is also sagging and leaking, the honest conversation moves toward replacement.

When does a swing-to-slide conversion make sense?

Sometimes the right repair for a French door is not a French door. Three situations come up regularly across Tampa Bay.

The swing gets in the way. French doors swing into a room or out onto a lanai. On a small lanai or against a pool cage they eat space and catch the wind. A sliding door opens the same width without swinging anywhere.

The threshold keeps leaking. A sliding door sill handles standing water better than most French door thresholds because its track is designed to drain. On a lanai that floods in every storm, a slider can be the more durable solution.

You are going impact anyway. If the door is in the wind-borne debris region and it is time to upgrade to impact glass, an impact sliding door is often the more practical choice for a wide opening.

The reverse conversion is common too, and we cover it in replacing a sliding glass door with French doors. Either direction is a permitted installation pulled by the installer of record, and a good company will tell you honestly which suits the opening. Our page on sliding glass door installation covers what a new slider involves.

What does a French door repair visit look like?

The technician works both doors, checks each hinge for play, sights the gaps for sag and racking, checks the sweep and threshold for wear and water staining, works the flush bolts and deadbolt, and looks at the glass and weatherstripping. You get a written flat quote before anything is done, and it depends on whether the door needs screws, hinges or jamb work, whether the threshold needs an insert, a re-bed or a sill pan, whether the astragal or bolts are involved, and whether any glass is being replaced. Everything except glass is done the same day with parts on the truck.

Palm Sliding Doors is a locally owned, insured company in South Tampa serving Hillsborough, Pinellas and Pasco, offering same-day French door repair with a free on-site inspection and a 1-year parts and labor warranty. If your French doors sag, stick or let water in, contact us and we will tell you what they need.

Frequently asked questions

Can a sagging French door be fixed without replacing it?

Yes in almost every case. Long screws through the top hinge, ball bearing hinge replacement or re-securing the jamb bring the door back up and square. Replacement is only the answer when the door or frame has rotted or corroded.

Why does my French door leak only during storms?

Wind-driven rain is pushing under a worn sweep or a cracked threshold insert, or wicking under a threshold that was never sealed to the slab. Replacing the seal, re-bedding the threshold and adding a sill pan or drip cap stops it.

What is the strip between two French doors called?

The astragal. It is fixed to the inactive door and gives the active door’s latch and deadbolt something to lock into. A loose or bent astragal causes leaks and locking problems.

Are French door repairs done the same day?

Hinges, thresholds, sweeps, astragals, flush bolts and weatherstripping are same-day repairs. Glass is measured first and fitted on a return visit once the tempered or laminated unit is made.

Should I replace French doors with a sliding door?

Consider it if the swing takes up space you need, the threshold floods in every storm, or you are upgrading to impact glass on a wide opening. Otherwise a sound French door is worth repairing.

Wesley Chapel homeowners in the newer communities can read about sliding glass door installation in Wesley Chapel, and the Wesley Chapel area hub lists the neighborhoods we serve.

References

Is Your Sliding Door Sticking, Leaking or Stuck?

Same-day service. Insured and locally owned. Upfront pricing and a 1-year parts and labor warranty across Tampa Bay.