Tampa Bay
Pocket Sliding Glass Door Repair in Tampa Bay
Pocket sliding glass door repair across Tampa Bay. Doors that slide into a wall pocket are hard to service because the rollers, track and interlocks hide inside the wall. We repair rollers, tracks, guides and locks on pocket and multi-slide doors, usually without cutting drywall, and re-tune the stack so every panel glides. Upfront pricing and a 1-year parts and labor warranty.
Same-day appointments
1-year parts and labor warranty
What to know
Pocket Door Repair in Tampa Bay: What to Know
Pocket door repair is a specialty, because a pocket sliding glass door hides its working parts inside the wall. These doors, common on lanai and pool walls in newer Tampa Bay homes and in waterfront builds in Apollo Beach, Tierra Verde and Palm Harbor, stack two, three or four panels and slide them into a wall pocket for a completely open wall. When one set of rollers wears or a guide breaks, the whole stack starts to bind, and most general handymen will not touch it.
Palm Sliding Doors repairs pocket and multi-slide doors without cutting into the wall whenever possible. We walk the panels out of the pocket in the right order, replace the rollers with stainless steel tandem sets rated for the panel weight, cap or replace the worn track, and renew the floor guides, interlock pile and locks. If something has fallen into the pocket, a common cause of a door that stops halfway, we clear it. Then the panels are re-stacked, each roller height is set so the interlocks meet, and the door is run through its full travel until every panel glides.
Repairing a pocket door is far less expensive than the replacement most homeowners fear, and it brings back the open-wall feel these doors were built for. The price depends on the number of panels and the parts needed, with a flat price before we start. Impact-rated pocket door replacements are quoted separately when a frame has failed. Every repair carries a 1-year parts and labor warranty.
Your Options
Stainless steel tandem rollers
Heavy-duty stainless sets sized to each panel, so the whole stack carries its weight evenly and stays quiet.
Stainless track caps
Formed caps that run the full length of the track, including the section inside the pocket, so the rail is smooth end to end.
Floor guides and pocket guides
Nylon and aluminum guides that keep the panels aligned as they enter and leave the pocket.
Interlock pile and seals
New weather pile on every interlock so the stacked panels seal against wind, rain and insects when closed.
Always Included
- On-site assessment and upfront flat price
- Panels extracted and re-stacked in the correct sequence
- Stainless steel tandem rollers rated for each panel
- Track cap or replacement inside and outside the pocket
- New floor guides, interlock pile and locks as needed
- Pocket cleared of debris and obstructions
- 1-year parts and labor warranty
What Affects Your Price
- Number of panels. Each sliding panel has its own rollers and guides, so a three-panel pocket door costs more to service than a two-panel one.
- Access to the pocket. Most panels walk out without opening the wall. If the pocket was built tight or the header has sagged, a small drywall access may be needed.
- Track and guide condition. A worn track gets a stainless cap; a cracked or corroded track in the pocket takes more work to replace.
- Panel weight. Impact-rated and eight-foot panels need heavy-duty rollers and two technicians to handle safely.
- Debris in the pocket. Clearing a pocket that has collected grit, pool toys or a fallen guide is usually quick but occasionally needs access.
Process
Our Pocket Door Repair Process
- 1
Assess the Pocket
We check how the panels stack, where they bind, and whether the rollers, track, guides or pocket itself is the problem.
- 2
Extract the Panels
Panels are lifted and walked out of the pocket in order, without opening the wall in most cases.
- 3
Replace & Repair
Rollers, track caps, floor guides, interlock pile and locks are replaced, and any obstruction in the pocket is cleared.
- 4
Re-stack & Tune
Panels go back in sequence, roller heights are set so they line up, and the door is tested through a full open and close.
Service areas
Where We Offer Pocket Door Repair
We offer pocket door repair in every community we serve. Select your area for local response times and details.
FAQ
Pocket Door Repair Questions, Answered
How much does pocket sliding door repair cost?
The number of panels that need rollers and whether the track needs a cap set the price. We give a flat price on site before we start.
Do you have to cut the wall open to repair a pocket door?
Usually not. The panels can be lifted and walked out of the pocket in sequence, which gives access to the rollers, track and guides. A small drywall access is only needed if the pocket was built tight or the header has sagged.
Why does my pocket door stop halfway?
Something is in the pocket, a floor guide has broken, or a roller on one panel has seized and is dragging the stack. We clear the pocket, replace the failed part and re-tune the panels.
Can you repair multi-slide doors that stack instead of pocketing?
Yes. Stacking three and four-panel doors use the same rollers, tracks and interlocks and are serviced the same way.
Do you replace pocket doors with impact-rated units?
Yes, when a frame has failed or a homeowner wants storm protection. Impact pocket and multi-slide doors are quoted by the opening with the permit handled.
Get Your Free Pocket Door Repair Estimate
Same-day service. Licensed and insured. Upfront pricing and a 1-year parts and labor warranty across Tampa Bay.