You can replace a sliding glass door with French doors in almost any Tampa Bay home, because both sit in a standard rectangular opening and the rough opening for a slider is usually close to what a pair of French doors needs. What changes is everything around the door: the way it swings into the room or the lanai, the threshold, the hardware, and, in Florida, the impact rating and the permit.
This guide walks through those changes so you know what you are signing up for, and the short list of things to check before you order a door. If you are weighing French doors against simply replacing the slider with a new one, the trade offs below should settle it either way.
Why homeowners make the switch
The usual reasons are practical rather than cosmetic. A French door gives a full width opening when both leaves are open, which a slider cannot, since one panel always stays in the frame. Hinged doors are easier for anyone who struggles with a heavy sliding panel. Many people simply prefer the look on a formal dining room, a master suite or an older Tampa bungalow where a slider always looked like an afterthought.
What to check first
Swing space. A pair of French doors needs room for two leaves to swing, either into the room or out onto the lanai. Inswing eats floor space and fights with furniture, rugs and pets. Outswing needs a clear patio and, on a screened lanai, enough depth that the doors do not hit the cage. Outswing is common in Florida because it is easier to make weathertight against wind driven rain and the door presses into its stops under pressure rather than away from them.
The opening itself. Measure the existing slider frame to frame. Standard sliders in Tampa Bay homes are often around six or eight feet wide and just under seven or eight feet tall. A pair of French doors of the same nominal size will usually go into the same rough opening, sometimes with a filler or a slightly rebuilt jamb. A very wide slider, ten or twelve feet, will not become one pair of French doors; that is a French door with fixed side lites, or a folding door, which is a different project.
The threshold and the floor. A sliding door sits on a low track. A French door sits on a sill with a raised threshold and a sweep at the bottom of each leaf, and it is the threshold that keeps water out of the house. The height of the interior floor and the lanai slab matters: if the lanai is at the same level as the inside floor, an outswing door needs a proper sill and the slab may need a small change so water does not sit at the door.
The wall and the header. A slider and a French door of the same width carry the same header, so a like for like width change rarely touches structure. Widening the opening does, and that is a permit and an engineer, not just a door.
Impact rating. In Tampa Bay’s wind borne debris region, a replacement exterior door generally needs to be a rated impact door or be protected by rated shutters. Impact French doors exist in every style, with laminated glass and a reinforced frame, and they are the version to buy if you do not want to put shutters over your new doors every storm.
Impact French doors: what is different
An impact French door is built to the same standard as an impact sliding glass door: laminated glass that stays in the frame when struck, a reinforced frame, and a multipoint lock that engages the frame top, middle and bottom. It carries a Florida Product Approval or a Miami Dade Notice of Acceptance for a stated design pressure.
Two details are specific to hinged doors:
- The astragal. Where the two leaves meet, one carries a vertical bar that the other closes against, with flush bolts or shoot bolts locking the inactive leaf into the frame at top and bottom. On an impact door this is a structural part, not trim. If it is loose, the pair is not rated.
- The hinges. Impact doors are heavy. The hinges and their screws into the jamb are part of the rating, and a sagging leaf later in life is usually a hinge that has worked loose, which is a French door repair rather than a new door.
What the installation involves
- Measure and quote. The installer measures the existing frame and rough opening, checks the floor and lanai levels, and confirms the swing. The quote depends on the door size, the glass package, whether it is impact rated, and how much the jamb and sill have to change.
- Permit. A replacement exterior door in Hillsborough or Pinellas County is a permitted job. The permit is pulled against the product approval and the door is inspected. Any installer who suggests skipping it is also skipping the part that makes your insurance credit and your resale inspection work.
- Remove the slider. The panels come out, then the frame. The opening is cleaned to the framing and checked for rot or damage, which is more common than you would expect under a thirty year old sill.
- Set the new frame. The frame is set plumb, level and square, shimmed and anchored to the approval’s schedule. The sill is bedded and sealed. This is where an outswing door earns its weather resistance.
- Hang, adjust and seal. The leaves are hung, the multipoint lock is adjusted so it engages without lifting, the astragal and bolts are set, and the exterior is flashed and sealed.
- Inspection. The county inspects, and you keep the paperwork with your product approval for the wind mitigation file.
The whole job is typically a day for a standard opening once the door arrives. Impact doors are built to order, and lead times stretch in storm season, so measure and order in the quiet months.
Slider or French door: the honest comparison
- Space. A slider takes no floor space. French doors take some, or take lanai space.
- Opening width. French doors open the whole width. A slider opens half, or two thirds on a three panel door.
- Weather. A well installed outswing French door seals tight. A slider relies on its track, weep holes and interlock, and it is the track that leaks on an old door.
- Effort. A hinged door is lighter to use than a big sliding panel on tired rollers, though a new slider on good rollers is easy too.
- Screens. A slider has a simple sliding screen. A French door needs a retractable screen or none, which matters on a lanai that is not caged.
- Security. Both are available with multipoint locks and laminated glass. Neither is inherently safer once you specify impact glass.
If the door mostly exists to get to the pool and you want the biggest simple opening for the money, a new sliding glass door is often the better answer. If the room wants a door that opens fully and looks like a door, French doors are worth it.
FAQ
Can any sliding glass door be replaced with French doors?
Nearly any standard six or eight foot slider can, because the rough opening is similar. Very wide sliders become a French door with side lites or a different door type, and that is a larger job.
Do I need a permit to replace a sliding door with French doors in Tampa?
Yes. A replacement exterior door is permitted in Hillsborough, Pinellas and the surrounding counties, and the permit is what documents the impact rating for insurance and resale.
Do French doors need to be impact rated in Florida?
In a wind borne debris region, a new exterior door generally needs to be impact rated or protected by a rated shutter. Impact French doors are available in every style and avoid the shutter.
Inswing or outswing for a Florida French door?
Outswing is the usual choice here. It keeps floor space free, seals better against wind driven rain, and presses into the frame under storm pressure. Inswing makes sense when the lanai has no room for the doors to swing.
Will French doors leak more than a slider?
Not when the sill is set and sealed properly. A hinged door with a raised threshold is generally easier to make weathertight than an aging slider track.
If you are thinking about the switch, book a free estimate for a sliding glass door installation and we will measure the opening, check the swing and the floor levels, and quote both options by the opening so you can compare them properly. We work across Tampa, Brandon, Clearwater and St. Petersburg.
References